Sharp Pencil

Sharp Pencil › Guides

What edge metal and drainage add to a commercial roof estimate

By The Sharp Pencil team

Last updated: 2026-11-13.

What do edge metal and drainage add to a commercial roof estimate?

Edge metal and drainage add their own lines to a commercial roof estimate. They're measured in linear feet and counts, not as a share of field area. Coping, gravel stop, drip edge and gutters are each measured by profile. Drains, overflow drains, scuppers and downspouts are each counted. Each line carries its source sheet, so the quantities are ready for your prices.

Disclosure: Sharp Pencil sells commercial roofing takeoffs, so we have a stake in this topic.

This page is about takeoff quantities, not plumbing, code, structural or warranty advice. It doesn't give unit prices. Your costs and your bid documents decide the job number.

An estimate that starts and stops at squares leaves these lines out. This page covers what edge metal and drainage put on your estimate, and what a miss does to it.

On a takeoff, each edge profile gets its own linear feet and each kind of drain, scupper and downspout gets its own count. Each line carries its source sheet. That leaves the quantities ready for your prices. The method for each line lives on its own page, and every section below links it.

Why roof area alone does not carry these lines

Edges are measured in linear feet. Drainage is counted. Neither quantity comes out of the field square feet.

Our checklist page says it plainly: "Linear feet and counted items move the number as much as field SF on a lot of commercial roofs." See the commercial roofing takeoff checklist.

One perimeter number does not fix it. A single "perimeter" total hides different products and prices.

Labor follows the same split. Our pricing walkthrough builds flashing and detail labor separately from field labor. See how to price a TPO roof.

For where these lines sit in a full takeoff, see how to do a roof takeoff.

What edge metal adds to the estimate

Edge metal is a family of lines, not one product. Our services page lists it this way: "Edge metal of every kind (coping, drip edge, gravel stop, gutters), downspouts, scuppers, counterflashing". Gutters are covered under drainage below.

On low slope, coping runs at the wall tops and gravel stop runs at the open edges. Fascia is its own line only when the detail shows a separate piece. Each one is its own linear feet, by profile.

Some of what edge metal adds is counted. Corners, end caps, splice plates and cleats go on the takeoff when the documents support them. Most edge metal is a length takeoff, but corners, joints, and cleats change the shop and install story when the documents call them out.

A blended number loses all of that. Blending coping and gravel stop into one "perimeter LF" hides the parts that price and fabricate differently.

Scuppers and outlets interrupt an edge run. The run is split as the plan keys it.

Coping is a linear foot line for the wall top. It does not replace the membrane lines under it. Termination bar is taken in linear feet from the detail, and parapet membrane on a commercial roofing takeoff covers it.

When the spec asks for a tested edge system and leaves the assembly open, that gap goes on the Questions tab.

For the method, see edge metal takeoff by profile. For the terms, see the commercial roofing estimating glossary.

What drainage adds to the estimate

Drainage is more than a drain count. Each drain, scupper and gutter run brings lines of its own.

Roof drains. Each one is a location with its own set of drain flashing. The plumber usually sets the drain body. The roofer flashes it, and that is where the lines come from.

Overflow drains. An overflow drain is not a spare. It is a second drain location with its own flashing.

Scuppers. Scuppers are counted with their size. Each one brings the sleeve or box, the membrane into the opening and the edge metal at the face, plus a conductor head and downspout if the elevations show one.

Gutters and downspouts. Gutters are taken in linear feet by size, with outlets, end caps and hangers as the gutter detail shows. Downspouts are taken by count and by length.

The length is the part that gets left behind. The count comes off the plan and the length comes off the elevations. Our pricing walkthrough gives an example: "Twenty-two downspouts on a 33-foot wall is roughly 730 linear feet of metal that a plan-only takeoff prices at zero." (Example assumptions, not a benchmark.) The same walkthrough builds flashing and detail labor separately from field labor. See how to price a TPO roof.

Sumps and crickets are counted and located on the takeoff, then flagged for the taper quote. See tapered insulation takeoff.

When the roof plan and the plumbing sheets show different counts, the takeoff carries the higher count with its source and puts the difference on the Questions tab. See roof plan counts vs the trade sheets.

The takeoff counts what the drawings show. It does not size drains, scuppers, gutters or downspouts.

For the method, see roof drainage on a commercial takeoff. For which sheets carry each item, see the sheets a roofing takeoff has to read.

Low slope and steep slope carry these lines differently

Low slope (TPO, EPDM, PVC, mod bit, BUR). The edge is coping, gravel stop and fascia, each its own linear feet by profile. The water leaves through roof drains, overflow drains and scuppers, each its own count. A low slope roof with a gravel stop can also drain to a gutter at the edge.

Steep slope (standing seam and shingle). Rake, eave, drip edge and gutters are each their own line, next to ridge, hip, valley, dead valley, starter, transitions, and endwall and sidewall flashing. Stopping at squares or a rough panel count leaves trim and flashing unpriced. The same holds on shingle. Starter, drip edge, and eave stay separate by default. See standing seam metal roof takeoff and asphalt shingle roof takeoff.

Gutters go on the takeoff in linear feet when the roofing scope owns them. When the bid documents leave that unclear, "who owns gutters" goes on the Questions tab.

Where two systems meet, the transition is its own line. See mixed-system commercial roof takeoff.

Edge and drainage lines, what each one adds and how it gets missed

Table 1. Edge and drainage lines, what each one adds and how it gets missed.
Line What it adds besides the main quantity How it gets missed Page with the detail
Coping Corners, end caps, splice plates and cleats when the detail shows them Blended with gravel stop into one perimeter number Edge metal takeoff
Gravel stop Corners and end conditions when detailed The run is not split where a scupper or outlet interrupts it Edge metal takeoff
Fascia Its own linear feet only when the detail shows a separate piece Counted twice, once as fascia and once inside the gravel stop Edge metal takeoff
Drip edge, rake and eave metal Separate lines by eave and rake when the set splits them Left off when the takeoff stops at squares or a panel count Standing seam, shingle
Gutters Outlets, end caps and hangers as the gutter detail shows Size not shown, or nobody confirmed who owns the gutters Roof drainage takeoff
Downspouts Length as well as count Counted from the plan with no length from the elevations Roof drainage takeoff
Scuppers The sleeve or box, the membrane into the opening, the edge metal at the face, and a conductor head where shown On the elevations but not on the roof plan Roof drainage takeoff
Primary roof drains One set of drain flashing per drain Counted from the roof plan only Roof drainage takeoff, roof plan vs trade sheets
Overflow drains A second location with its own flashing Treated as a spare and left off Roof drainage takeoff
Sumps and crickets A count and a location for the taper quote On the roof plan but missing from the taper layout Tapered insulation takeoff

Common ways these lines come up short

Anything the set leaves open belongs on the Questions tab, not in a guessed quantity.

Before the bid leaves, run the commercial roofing takeoff checklist. For how to write up the open items, see what a roofing RFI register should contain.

What you price, and what comes back UNPRICED

You price the job and you submit the bid. The takeoff supplies the quantities.

Pricing is optional. Send your cost data and we apply your prices to the quantities. Any line you have not priced comes back marked UNPRICED.

Edge metal lines roll into sticks or pieces on the material order list. See from takeoff to material order.

For the pricing step, see how to bid a commercial roofing job and how to price a TPO roof.

What you get back from Sharp Pencil

Every quantity carries its source sheet and its basis.

Four files: START HERE, marked-up drawings PDF, Takeoff.xlsx with a Questions tab, and the material order list.

We take off steep slope (standing seam, shingle) and commercial low slope (TPO, EPDM, PVC, mod bit, BUR) from the full set.

See what a roofing takeoff includes, commercial roofing takeoff services and a sample takeoff. For the service itself, see what a takeoff costs to buy.

FAQ

What do edge metal and drainage add to a commercial roof estimate?

Edge metal and drainage add their own lines to a commercial roof estimate. They're measured in linear feet and counts, not as a share of field area. Coping, gravel stop, drip edge and gutters are each measured by profile. Drains, overflow drains, scuppers and downspouts are each counted. Each line carries its source sheet, so the quantities are ready for your prices.

Do edge metal and drainage add a set percent to a commercial roof bid?

We don't publish a set percent. Edge metal and drainage are their own lines on the takeoff, in linear feet and counts, and the total depends on what the drawings show. You put your prices on those quantities.

Why can't I price edge metal and drainage from roof area alone?

Because they are not area lines. Edges are measured in linear feet by profile, and drains, scuppers and downspouts are counted. A single perimeter total hides different products and prices.

Is edge metal one line on the takeoff?

No. Edge metal is a family of lines. Coping, gravel stop, drip edge and gutters each get their own linear feet, split by profile when the drawings split them. See the edge metal takeoff guide.

Who prices the edge metal and drainage lines?

You do. Pricing is optional. Send your cost data and we apply your prices to the quantities. Any line you have not priced comes back marked UNPRICED.

What if the drawings leave the coping profile or gutter size open?

That gap goes on the Questions tab. The takeoff does not guess a profile, a size or a unit price.

What does a takeoff from Sharp Pencil cost?

First takeoff free, one per contractor, on a job you're bidding or quoting. After that, see pricing.

What does Sharp Pencil send back?

Four files: START HERE, marked-up drawings PDF, Takeoff.xlsx with a Questions tab, and the material order list. Every quantity carries its source sheet and its basis. Usually within one business day. Delivered within 48 hours*.

*Clock starts once any questions we send you are answered.

Why send it to us

*Clock starts once any questions we send you are answered.

Try it on a job you are bidding

Get your first takeoff free · See pricing · See a sample takeoff

The Sharp Pencil team